Just How to Remove as Well as Replace a Bath Tub
Just How to Remove as Well as Replace a Bath Tub
Blog Article
We have encountered this article relating to A Step-by-Step Guide to Installing a Bathtub down the page on the web and thought it made perfect sense to talk about it with you here.
Mounting a bathtub isn't specifically rocket science, but it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably tough project. If the old bathtub is easily available, the task can relocate quickly; if you need to open a wall surface to get rid of the old bathtub as well as position the new tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will need a helper to move out the old tub as well as set in the new one. Make certain you have qualified yourself for the work as well as fit trying it. Instead of employing a service provider to take over a halfway-completed job, it is far better to consider utilizing one prior to you start. Chances are you might need a specialist plumber to make tube links.
This article will certainly assist you install a brand-new bathtub in your restroom if you have currently gotten a new tub and also do not need to change the setup of your previous water system pipes.
Your devices and material checklist need to consist of the following:
Getting ready for the Setup
First of all, the sustaining framework supplied with the bathroom should be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to avoid pressure on the bath tub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of eliminating the existing taps can be rather troublesome because of the restricted gain access to that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a fabric ready for the remaining water that will come from the pipes. Once the supply pipes have been removed, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are helpful in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bathtub until the level checks out level.
To mount faucets, fit all-time low of the furthest flexible tap adapter to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Activate the water as well as inspect all joints and new pipework for leakages as well as tighten them if required. Fill the bath tub as well as also check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait until the bath tub has actually been used at the very least once as this will certainly settle it right into its final position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin ensuring that the washers are in area between the faucet and the sink. Protect the faucet in place with the supplier offered backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a stiff seal, creating the water to penetrate the wall between the bathroom and also the tiling, leading to problems with moisture as well as feasible leakages to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and fittings. They are offered in tubes as well as cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can fracture rather very early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the market. It is advisable to fit the ceramic tiles using waterproof or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very excited about A Step-by-Step Guide to Installing a Bathtub and I really hope you enjoyed my blog entry. Enjoyed our piece of writing? Please share it. Help someone else discover it. Thanks a lot for taking the time to read it.
Quote
Report this page